Aopen AX3S Pro II Driver
Find great deals for mb RAM Memory for AOPEN Ax3s Pro II (pc) - Motherboard Memory Upgrade. Shop with confidence on eBay! AOpen AX3S Pro II Motherboard Memory. Maximum Memory MB Memory Slots 3 (3 banks of 1) non-removable base memory 0MB. 64MB Aopen pin. To determine part numbers for the AOpen AX3S Pro II motherboard we used best guess approach based on CPU model, frequency and.
|Supported systems:||Windows 2008, Windows XP, Windows Vista, Windows 7/8/10|
|Price:||Free* [*Free Registration Required]|
Aopen AX3S Pro II Driver
I assume the higher clock is only for the Pro version, though nowhere is this mad clear. Given the good stability I get off this, I was left itching for higher settings. Setting it up In short, this should be pretty easy for anyone Aopen AX3S Pro II to installing new motherboards. Its a bog-standard ATX size and the only jumper you really need to play with is the one to disable onboard sound.
Everything else is handled from within the BIOS. As I mentioned above, the maximum FSB available to me wasnot as stated on the spec sheet. Vcore setting is available but at first I thought it was resetting itself to Aopen AX3S Pro II default every time I rebooted. After much fiddling about, I discovered Aopen AX3S Pro II I could only make it stick by hitting the 'Save settings' F-key from within that BIOS screen, not from the main menu.
Finally, on the good side, the BIOS can take readings off the boards inbuilt Winbond heat-sensors CPU and casewhich saves fiddling about Aopen AX3S Pro II thermistors. I did briefly try getting it to run without doing a proper Windows reinstall, and of course it went flaky.
In particular it caused some cross-linked file Aopen AX3S Pro II on my Maxtor hard drive which Windows ME seemed incapable of fixing, requiring a run at DOS scandisk. I can't really fault the board for this, I'm just the eternal optimist Aopen AX3S Pro II a bit lazy. Windows ME seems to have all the drivers it needs for the chipset as part of the package, so I did not bother with the supplied driver disk.
Everything seemed happy once I did a proper reinstall. One final note in this section is on RAM.
These boards only take up to megs of RAM in total, which could be a limiting factor for some people in 6 months from now. As it is, a lot of gamers have Aopen AX3S Pro II of RAM, and I can foresee it not being long before this doubles again. A final moan is that it won't accept one of my DIMMs generic stuff, but it works fine in my other systems.
AOpen AX3S Pro II BIOS הורדה בחינם (ver. 1.11)
Again I have read similar complaints elsewhere about boards not accepting Aopen AX3S Pro II RAM, so be prepared for a bit of frustration if you have old RAM you want to use on the board. Overclocking and benchmarks Right then, down to the good stuff.
My processor is one of the very first flip-chip P3 s to be released. Given I doubt anyone who reads this actually runs boards at default clock speeds, Aopen AX3S Pro II give you the Sandra benchies run from MHz on my P3 i. For stable work of processors at high frequency the voltage jumps on the supply filter's output mustn't exceed mV at the supply voltage equal 2V.
For uF capacitors of this board this figure is equal to mV. After installation of a new BIOS version 1. The Aopen company states that its Pro-version shows even better results.
Aopen AX3S Pro II Unfortunately, we couldn't compare the results, since we couldn't fetch this board. As for a cooler installation, on the first look the board seems to have enough space for it. But in practice, we had difficulty in installing even Aopen AX3S Pro II usual Intel cooler, not to mention Golden Orb. Another peculiarity is that all slots are shifted to the left side; so, AGP slot isn't located tight to the ports anymore.
With this layout an installed AGP-videocard doesn't prevent any manipulation with memory clips. When developing an electric design of the boards, AOpen used the Frequency Isolation Wall technology. The idea of this technology is the following: A power supply jack hasn't a good location as well. The cable doesn't leave enough space for a cooler.
The board has 3DIMM slots, though this is more than enough for i northbridge you won't be able to set more than MBytes memory.